The Prospector News

Titan Mining Discovers Near-Mine Open-Pitable Mineralization at Empire State Mine, Including 15 Feet Grading 12.4% Zinc

You have opened a direct link to the current edition PDF

Open PDF Close
Uncategorized

Share this news article

Titan Mining Discovers Near-Mine Open-Pitable Mineralization at Empire State Mine, Including 15 Feet Grading 12.4% Zinc

 

 

 

 

 

Titan Mining Corporation (TSX:TI) is pleased to announce the results from surface drilling at its 100%-owned Empire State Mine in New York State. The current drill program is focused on two recently-identified near-surface zinc targets (Figures 1 and 2). The Hoist House zone is interpreted as an extension of the large #2 mine, which accounted for approximately half of the tons mined historically at ESM, and the Turnpike zone as an extension of the historic #1 mine. To date, three holes have been completed at the Hoist House zone and drill testing of this zone continues. A second drill has begun initial testing of the Turnpike zone.

 

Key mineralized intervals from the Hoist House zone include:

 

  • 15 feet assaying 12.4% zinc
  • 15.5 feet assaying 8.0% zinc
    • Including 4.3 feet assaying 19.3% zinc
  • 70 feet assaying 2.2% zinc
    • Including 3.5 feet assaying 11.7% zinc
  • 56 feet assaying 2.0% zinc
    • Including 14.5 feet assaying 5.0% zinc

 

Don Taylor, Chief Executive Officer, commented, “We have identified several near-surface targets at the mine site, and in the district, which we believe present an opportunity for ESM to add low-cost near-term production. The zones have good continuity along strike as well as at depth and contain higher grade zinc mineralization interbedded with lower grade lenses that can be accessed through open pit mining. The current drill program will allow us to evaluate the zones quickly for potential mining. We are initially focusing on targets near the existing infrastructure and, if economic, these new zones could provide incremental mill feed to help fill existing capacity at ESM. Existing permits allow for open pit mining and we will work with regulators to determine if any additional studies are required.”

 

Scott Burkett, Vice President, Exploration, stated, “We have been very pleased with the continuity and size of the mineralized zones as indicated by surface drilling. The mineralogy and coarse-grained sulphides are similar to the #2D zone currently being developed for underground mining and, as such, we anticipate that the processing method and recovery rates will be similar. Metallurgical samples have been collected and testing has begun onsite.”

 

The Hoist House zone is located one mile south of the ESM #4 mine and milling complex and is interpreted to be the unmined extension of the historic #2 zone. Historic drilling indicates that the Hoist House zone extends to a depth of at least 300 feet over a strike length of 600 feet. It consists of two mineralized horizons, the hanging wall and footwall horizons, with a range of thickness of 10 to 20 feet and 30 to 70 feet, respectively (Figure 3).

 

A second zone currently being drill tested is the Turnpike zone, which was identified based on the interpreted geology. The Turnpike zone is located 600 feet to the southeast of the Hoist House zone and is interpreted to be the unmined extension of the historic #1 zone. Historic mapping identified outcropping mineralization with a strike length of 450 feet, and historic drilling indicates that the zone is between 20 and 50 feet thick.

 

SX19-2475 is an inclined hole drilled from surface, targeting the Hoist House zone. The drill hole intercepted the HW and FW mineralized horizons. It confirmed the presence of near-surface mineralization and revealed robust lower-grade mineralization in the FW horizon. Significant mineralized intervals were:

 

  • 11 feet assaying 6.4% zinc (HW)
  • 56 feet assaying 2.0% zinc (FW)
    • Including 14.5 feet assaying 5.0% zinc

 

SX19-2476 is an inclined hole drilled from surface on the same section as SX19-2475. The drill hole targeted HW and FW mineralization down dip from SX19-2475. The drill hole intercepted the HW and FW mineralized horizons, demonstrating the down-dip continuity of mineralization and confirming the presence of the FW horizon. Notable mineralized intervals were:

 

  • 15.5 feet assaying 8.0% zinc (HW)
    • Including 4.3 feet assaying 19.3% zinc
  • 35.6 feet assaying 3.1% zinc (FW)

 

SX19-2477 is an inclined hole drilled from surface. The hole is an infill hole which was drilled between SX19-2475 and SX19-2476 and completed the drill fan linking the HW and FW mineralized horizons together down dip. Noteworthy mineralized intervals were:

 

  • 15 feet assaying 12.4% zinc (HW)
  • 70 feet assaying 2.2% zinc (FW)
    • Including 3.5 feet assaying 11.7% zinc

 

For a full list of the Hoist House mineralized intervals from these holes, refer to Table 1.

 

Figure 1 – Location of Near-Surface Drill Targets at ESM

 

https://www.globenewswire.com/NewsRoom/AttachmentNg/c67a4158-0094-4465-b287-afe6e3878f4a

 

Figure 2 – Plan View of Hoist House and Turnpike Zones Showing Drill Hole Locations

 

https://www.globenewswire.com/NewsRoom/AttachmentNg/baf235cd-8cc2-46be-bf98-426dc3da704e

 

Figure 3 – Cross Section of Hoist House Zone Looking Northeast and Showing Drill Holes and Selected Mineralized Intervals

 

https://www.globenewswire.com/NewsRoom/AttachmentNg/5ff2257b-44ee-4b95-b1db-e0e19bcea277

 

Table 1 – Exploration Drill Results from Hoist House Zone at ESM

 

Drill hole From (feet)  To (feet) Interval (feet)1 From (meters) To (meters) Interval (meters)1 Zn%
Horizon
SX19-2475 66.5 77.5 11.0 20.3 23.6 3.4 6.4 HW
SX19-2475 172.0 228.0 56.0 52.4 69.5 17.1 2.0 FW
  Including 201.5 216.0 14.5 61.4 65.8 4.4 5.0 FW
                 
SX19-2476 77.5 93.0 15.5 23.6 28.3 4.7 8.0 HW
  Including 83.7 88.0 4.3 25.5 26.8 1.3 19.3 HW
SX19-2476 237.4 273.0 35.6 72.4 83.2 10.8 3.1 FW
                 
SX19-2477 73.3 88.3 15.0 22.3 26.9 4.6 12.4 HW
SX19-2477 192.0 262.0 70.0 58.5 79.9 21.3 2.2 FW
  Including 201.5 205.0 3.5 61.4 62.5 1.1 11.7 FW

1 Based on observed geologic contacts, data suggest drill interval is within 10% of true thickness, however, based on the drill density it is not possible to determine the true with of the zone(s) and no representation is made here regarding the true width.

 

Qualified Person

 

The results of the Titan drilling have been reviewed, verified and compiled by Donald R. Taylor, MSc., PG, Chief Executive Officer of Titan, a qualified person as defined by National Instrument 43-101 (NI 43-101). Mr. Taylor has 30 years of mineral exploration and mining experience, and is a Registered Professional Geologist through the SME (registered member #4029597).

 

Assays and Quality Assurance/Quality Control

 

To ensure reliable sample results, the Company has a rigorous QA/QC program in place that monitors the chain-of-custody of samples and includes the insertion of blanks and certified reference standards at statistically derived intervals within each batch of samples. Core is photographed and split in half with one-half retained in a secured facility for verification purposes.

 

Sample preparation (crushing and pulverizing) has been performed at ALS Geochemistry, an ISO/IEC accredited lab located in Sudbury, Ontario, Canada. ALS Minerals Laboratories prepares a pulp of all samples and sends the pulps to their analytical laboratory in Vancouver, B.C., Canada, for analysis. ALS analyzes the pulp sample by an aqua regia digestion (ME-ICP41 for 35 elements) with an ICP – AES finish including Cu (copper), Pb (lead), and Zn (zinc). All samples in which Cu (copper), Pb (lead), or Zn (zinc) are greater than 10,000 ppm are re-run using aqua regia digestion (Cu-OG46; Pb-OG46; and Zn-OG46) with the elements reported in percentage (%). Silver values are determined by an aqua regia digestion with an ICP-AES finish (ME-ICP41) with all samples with silver values greater than 100 ppm repeated using an aqua regia digestion overlimit method (Ag-OG46) calibrated for higher levels of silver contained. Gold values are determined by a 30 g fire assay with an ICP-AES finish (Au-ICP21).

 

About Titan Mining Corporation

 

Titan is an Augusta Group company which produces zinc concentrate at its 100%-owned Empire State Mine located in New York State. ESM is a group of zinc mines which started production in the early 1900s. Titan is built for growth, focused on value and committed to excellence. The company’s shares are listed under the symbol “TI” on the Toronto Stock Exchange.

 

Posted November 21, 2019

Share this news article

MORE or "UNCATEGORIZED"


VIZSLA SILVER AGREES TO ACQUIRE NEWLY CONSOLIDATED PAST-PRODUCING SILVER DISTRICT IN THE EMERGING SILVER-GOLD-RICH PANUCO - SAN DIMAS CORRIDOR IN MEXICO

Vizsla Silver Corp. (TSX-V: VZLA) (NYSE: VZLA) (Frankfurt: 0G3) i... READ MORE

March 28, 2024

Additional Drill Results Highlighted by Hole D-380 in Block 6 at Oko West, Intersecting 39.7 m Grading 5.27 g/t Au Including 2.8 m @ 14.18 g/t Au and 13.0 m Grading 10.50 g/t Au

Reunion Gold Corporation (TSX-V: RGD) (OTCQX: RGDFF) is pleased t... READ MORE

March 28, 2024

STLLR Gold’s Tower Gold Project Infill Drilling Continues to Confirm Mineralization at the Jonpol Deposit

STLLR Gold Inc. (TSX: STLR) (OTCQX: STLRF) (FSE: O9D) announces ... READ MORE

March 28, 2024

Hudbay Provides Annual Reserve and Resource Update and Production Outlook

Consolidated copper production is expected to average 153,000i to... READ MORE

March 28, 2024

Aya Gold & Silver: Record 2023 Production, Revenue and Operating Cash Flow

Aya Gold & Silver Inc. (TSX: AYA) (OTCQX: AYASF) is pleased t... READ MORE

March 28, 2024

Copyright 2024 The Prospector News