The Prospector News

Drilling at the SW Zone at San Albino Intersects 62.04 g/t Gold Over 1.5 Meters (Estimated True Width) 15 Meters from Surface and Outside of the Delineated Resource

You have opened a direct link to the current edition PDF

Open PDF Close
Uncategorized

Share this news article

Drilling at the SW Zone at San Albino Intersects 62.04 g/t Gold Over 1.5 Meters (Estimated True Width) 15 Meters from Surface and Outside of the Delineated Resource

 

 

 

 

 

Mako Mining Corp. (TSX-V: MKO); (OTCQX: MAKOF) is pleased to report positive drill results from expansion drilling at its San Albino gold project in northern Nicaragua.

 

The objective of this drill program was to target the SW Zone at San Albino, where very limited mineral resources (approximately 0.4%) were estimated by Mine Development Associates a division of RESPEC, out of Reno, Nevada.  A technical report for the updated mineral resource estimate was filed in accordance with National Instrument 43-101, Standards of Disclosure for Mineral Projects (“NI 43-101”) filed under the Company’s SEDAR profile at www.sedar.com and available on the Company’s website at www.makominingcorp.com (see press release dated October 19, 2020).

 

Highlights

 

  • Intersected shallow high-grade mineralization outside of the MDA Resource
    • 62.04 g/t Au and 28.55 g/t Ag over 2 meters (“m”) (1.5 m estimated true width) interval comprising quartz vein with visible gold in drill hole SA20-443 approximately 15 m from surface
  • Potential for another near surface vein with a strike extent of at least 120 m
    • 29.4 g/t Au and 28.0 g/t Ag over 0.70 m in trench SA20-TR2-51 approximately 2 m from surface in a shallowly dipping quartz vein

 

Akiba Leisman, Chief Executive Officer of Mako states that, “when the MDA Resource was released, we stated that San Albino was open along strike and down dip.  As is the case with many areas of San Albino, the SW Zone required additional drilling to better understand the geology before delineating a mineral resource.  These results confirm the existence of near surface high-grade gold, which we expect to convert to mineral resources at San Albino as the drilling program advances.  Importantly, exploration is continuing at Las Conchitas to the south, where we also expect to find additional mineral resources.”

 

Specific comments on significant results reported in this press release are as follows:

 

SA20-443 intersected 62.04 g/t Au and 28.55 g/t Ag over 2 m (1.5 m estimated true width).  SA20-443 was drilled to test the strike projection of the quartz vein identified in previous trenching and drilling programs (see attached drill plan and sections).  The hole is located 26 m along strike to the southwest from discovery hole AR11-12, which intersected 22.74 g/t Au over 8.0 m, including 9.67 g/t Au and 16.6 g/t Ag over 3 m and 43.66 g/t Au and 130.6 g/t Ag over 3.5 m (see press release dated September 19, 2013).

 

Trench SA13-TR11-EXPPIT#1 located approximately 160 m along strike and to the southwest of SA20-443 (see attached drill plan) exposed a vein with a true width of 1.8 m grading 13.94 g/t Au and 18.9 g/t Ag, indicating additional strike potential which will be tested with drilling this year.

 

Detailed mapping of the area has identified multi-stage deformation structures, with the latest deformation event represented by NE-SW faulting.  The current interpretation indicates the faults may have displaced the vein in a manner that has upthrown blocks across the faults bringing the mineralized zone closer to surface than the previous down dip projections.

 

SA20-TR-51 encountered a high-grade vein with a vertical sample (estimated true width) grading 29.40 g/t Au and 28.0 g/t Ag over 0.7 m and appears to indicate the potential of another near surface vein with a strike length of at least 120 m (see attached drill plan).

 

Overall geologic mapping, surface sampling and limited drilling has identified a prospective area at the SW Zone measuring approximately 400 x 400 m, which is roughly the size of the current MDA Resource footprint.  A detailed understanding of the geometry and geology is critical to expanding mineralized zones for future mineral resource additions. This area is complex, with localized faulting, and will require close spaced drilling which the Company plans to conduct this year.

 

An aggressive drilling program is planned for the area with the objective of identifying additional resources within the currently permitted pit limit.  Approximately 7 kilometers of drill roads have been prepared for the upcoming drilling program.

 

The SW Zone currently remains open at depth and along strike (see attached sections).  Since 2020, the Company has only drilled a total of 371.30 m in 9 drill holes.  Several drill holes have encountered mineralized intervals with visible gold.  The Company anticipates receiving results in the coming weeks from remaining drill holes and will be released in due course.

 

Assay Results Reported in This Press Release

 

Drill Hole From
(m)
To

(m)

Width
(m)*
Au
(g/t)
Ag
(g/t)
Interval True
Width
(m)**
SA20-441 6.00 7.50 1.50 0.15 0.7 Anomalous values 4.2
7.50 9.00 1.50 0.86 5.0
9.00 10.50 1.50 0.10 1.0
SA20-442 14.50 15.20 0.70 1.89 6.4 1.68 g/t Au and 4.72 g/t Ag over 1.85m 1.65
15.20 16.35 1.15 1.55 3.7
SA20-443 15.00 16.00 1.00 1.28 2.2 62.04 g/t Au and 28.55 g/t Ag over 2.00m 1.5
16.00 17.00 1.00 122.80 54.9
SA20-444 0.00 1.20 1.20 3.11 2.50 3.11 g/t Au and 2.5 g/t Ag over 1.2m 1.1
5.00 6.00 1.00 1.97 6.2 2.13 g/t Au and 7.2 g/t Ag over 2.10m 2.0
6.00 7.10 1.10 2.28 8.1
SA20-445 8.90 9.90 1.00 5.55 4.6 5.54 g/t Au and 4.6 g/t Ag over 1.00m 0.9
SA20-446 25.80 26.30 0.50 0.60 1.0 Anomalous values 1.0
26.30 27.05 0.75 0.40 1.6
30.50 32.00 1.50 0.15 0.6 Anomalous values 1.3
SA20-447-449 Results pending

 

The mineralized intervals shown above utilize a 1.0 g/t gold cut-off grade with not more than 1.0 meter of internal dilution. *Widths are reported as drill core lengths.  ** True width is estimated from interpreted sections.

 

Sampling, Assaying, QA/QC and Data Verification

 

Drill core was continuously sampled from inception to termination of the entire drill hole.  Sample intervals were typically one meter.  Drill core diameter was HQ (6.35 centimeters).  Geologic and geotechnical data was captured into a digital database, core was photographed, then one-half split of the core was collected for analysis and one-half was retained in the core library.  Trench and surface channel samples followed a similar procedure as drill core sampling.  Continuous samples were collected using a diamond saw or rock hammer and chisel.  Care was taken to ensure a consistent channel width of 6 cm wide and 5 cm depth.  Individual channel samples range from 0.4 meters to 1.0 meters in length. Both drill core and channel samples were kept in a secured logging and storage facility until such time that they were delivered to the Managua facilities of Bureau Veritas and pulps were sent to the Bureau Veritas laboratory in Vancouver for analysis.  Gold was analyzed by standard fire assay fusion, 30 gram aliquot, AAS finish.  Samples returning over 10.0 g/t gold are analyzed utilizing standard Fire Assay-Gravimetric method.  The Company follows industry standards in its QA&QC procedures. Control samples consisting of duplicates, standards and blanks were inserted into the sample stream at a ratio of 1 control sample per every 10 samples.  Analytical results of control samples confirmed reliability of the assay data.

 

Qualified Person

 

John M. Kowalchuk, P.Geo, a geologist and qualified person (as defined under NI 43-101) has read and approved the technical information contained in this press release. Mr. Kowalchuk is a senior geologist and a consultant to the Company.

 

About Mako

 

Mako Mining Corp. is a publicly listed gold mining, development and exploration company. The Company is developing its high-grade San Albino gold project in Nueva Segovia, Nicaragua. Mako’s primary objective is to bring San Albino into production quickly and efficiently, while continuing exploration of prospective targets in Nicaragua.

 

 


SA AR SCHEMATIC LONG SECTION – PR- MARCH 11 2021 V3 (CNW Group/Mako Mining Corp.)

 

 


SA -SW ZONE SCHEMATIC CROSS SECTION – PR- MARCH 12 2021 (CNW Group/Mako Mining Corp.)

 

 


SAN ALBINO – SW ZONE DRILLING PROGRAM – 1 2500 – PR- MARCH 15 2021 v5 (CNW Group/Mako Mining Corp.)

 

Posted March 16, 2021

Share this news article

MORE or "UNCATEGORIZED"


VIZSLA SILVER AGREES TO ACQUIRE NEWLY CONSOLIDATED PAST-PRODUCING SILVER DISTRICT IN THE EMERGING SILVER-GOLD-RICH PANUCO - SAN DIMAS CORRIDOR IN MEXICO

Vizsla Silver Corp. (TSX-V: VZLA) (NYSE: VZLA) (Frankfurt: 0G3) i... READ MORE

March 28, 2024

Additional Drill Results Highlighted by Hole D-380 in Block 6 at Oko West, Intersecting 39.7 m Grading 5.27 g/t Au Including 2.8 m @ 14.18 g/t Au and 13.0 m Grading 10.50 g/t Au

Reunion Gold Corporation (TSX-V: RGD) (OTCQX: RGDFF) is pleased t... READ MORE

March 28, 2024

STLLR Gold’s Tower Gold Project Infill Drilling Continues to Confirm Mineralization at the Jonpol Deposit

STLLR Gold Inc. (TSX: STLR) (OTCQX: STLRF) (FSE: O9D) announces ... READ MORE

March 28, 2024

Hudbay Provides Annual Reserve and Resource Update and Production Outlook

Consolidated copper production is expected to average 153,000i to... READ MORE

March 28, 2024

Aya Gold & Silver: Record 2023 Production, Revenue and Operating Cash Flow

Aya Gold & Silver Inc. (TSX: AYA) (OTCQX: AYASF) is pleased t... READ MORE

March 28, 2024

Copyright 2024 The Prospector News