Arizona Gold Corp. (TSX: AZG) (OTCQB: AGAUF) provides additional underground drilling results and drilling program update at its 100% owned Copperstone gold project located in Arizona, United States.

Giulio Bonifacio, President & CEO of Arizona Gold, stated: “We are pleased to announce additional results from the underground core drilling program which continues to show continuity and extension in mineralized domains over good mining widths. Additionally, we see further indications of previously unknown mineralization below the previously defined mineralized domain CUVND3, which is indicated in Figure 2. We are now moving forward with in-fill definition drilling of planned stopes, which will provide information for final stope design planning, as shown in Figure 1. Additionally, upon completion of the current phase of drilling, the Company will provide an updated resources estimate which will also include drilling results from 5,000 meters of successful drilling in 2019.”

Drilling Highlights Include

Drill Hole AZG-21-13-12

• 1.5 m at 22.07 g/t gold (“Au”), and 1.2 m at 11.73 g/t Au

Drill Hole AZG 21-13A-18

• 4.7 m at 2.34 g/t Au; including 0.9 m at 5.33 g/t Au

Drill Hole AZG-20S-23

• 15.2 m at 3.27 g/t Au; including 6.1 m at 6.02 g/t Au

Drilling Update

The underground exploration core hole drilling is ongoing and has focused on the D zone of the Copperstone shear zone. Continuity and extension of mineralized domains were realized in many holes. Figure 1 shows the new drilling in plan view. Figures 2, and 3 show the drilling in cross section, and Table 1 summarizes drill hole assay results. Drill hole intervals of prior drill programs mentioned in this release are as follows:

Drill Hole A98-5

• 170.1 – 171.6; 1.5m at 7.03 g/t Au (CUVND2)
  •  173.1 – 179.4; 6.2m at 21.59 g/t Au (CUVND3)

Drill Hole CSD-9

• 149.2 – 154.8; 5.6m at 8.33 g/t Au (CUVND2)
  •  157.0 – 160.8; 3.8m at 0.91 g/t Au (CUVND3)

Drill Hole KER-17U-16

• 15.2 – 16.3; 1.1m at 20.70 g/t Au (CUVND3)

Drill Hole CS-367

• 155.4 – 160.0; 4.6m at 8.16 g/t Au (B Zone)

Continued Indication of New Domain Below CUVND3

Drill hole AZG-21-13A-18 intersected 0.8 m at 1.14 g/t Au, indicating a possible new domain 18m below the CUVND3 domain. This adds a fourth hole showing the possible new domain. Drill hole AZG-20S-16 intersected 1.5 m at 2.69 g/t Au, indicating the potential for a new domain below the CUVN domain. Historic drilling in this area has not shown strong Au mineralization, so there is potential for resource expansion with additional drilling. The following provides additional information for each of the drill holes reported above (Also See Figures 1 through 3):

AZG-21-10-17 is an up angle core hole drilled northwesterly and collared in station 10 in the D Zone. It intersected 4.8 m at 3.32 g/t Au (including 0.9 m at 7.13 g/t Au and 1.2 m at 5.47 g/t Au), successfully extending the CUVND3 domain about 27.4 m up dip. The hole also intersected 0.8 m at 14.80 g/t Au, which is a possible extension of the CUVND domain about 15.2 m up dip from its current modelled extent.

AZG-21-13-12 is an up angle core hole drilled northeasterly and collared in station 13 in the D Zone. It intersected 1.5 m at 22.07 g/t Au, successfully targeting the CUVND3 domain about 29 m up dip of drill hole A98-5, about 12.2 m down dip of drill hole CSD-9 and about 15.2 m along strike to the northwest of drill hole KER-17U-16. It also intersected 1.2 m at 11.73 g/t, successfully targeting the CUVND2 domain about 26 m up dip of A98-5, and 15.2 m down dip of CSD-9..

AZG-21-13A-18 is an up angle hole drilled to the west and collared in station 13A in the D zone. It intersected 4.7 m at 2.34 g/t Au (includes 0.9 m at 5.33 g/t Au), about 7.5 m above the CUVND domain, which might be an offset of the domain or a new domain. The hole also intersected 0.8 m at 1.14 g/t Au, indicating a possible new domain 18m below the CUVND3 domain.

AZG-20S-16 is a surface down angle RC hole drilled westerly from the east side of the pit into the C Zone, with a total depth of 305 m. It intersected 9.1 m at 1.98 g/t Au (includes 3.0 m at 3.57 g/t Au), successfully targeting the C Zone mineralization where modelled. It also intersected 1.5 m at 2.69 g/t Au, indicating the potential for a new domain below the CUVN domain, which may be related to the Footwall Zone. Historic drilling in this area has not shown strong Au mineralization, so there is potential for resource expansion with additional drilling.

AZG-20S-23 is a surface down angle RC hole drilled northwesterly from the east side of the pit into the B Zone, with a total depth of 172 m. It targeted and successfully intersected 15.2 m at 3.27 g/t Au (includes 6.1 m at 6.02 g/t Au), also intersecting 1.5 m at 1.24 g/t Au. The intercepts confirm grade and mineralization 6 m down dip from historic drillhole CS-367.

The underground exploration drilling program is nearing completion. The primary focus of the drilling program has been to extend the known mineralized domain boundaries and demonstrate continuity of mineralization in areas where drill hole spacing was greater than average. The Copperstone Mine has historically produced, via open pit mining and a whole ore leach gold processing plant, over 500,000 ounces of gold at an average grade of about 3 g/t Au.

Table 1: Underground Core and Surface RC Drilling Results

Figure 1: Underground & Surface Hole Locations – Results with Representative Ore Domains Shown – Plan View:

https://www.globenewswire.com/NewsRoom/AttachmentNg/3d65198a-aa2c-4975-8eec-7ea013947bf0

Figure 2: Cross Section A-A’ Underground Core Holes:

https://www.globenewswire.com/NewsRoom/AttachmentNg/3fc79510-c1c3-4647-ac91-091d8e8c6857

Figure 3: Cross Section B-B’ Surface Hole AZG-20S-16:

https://www.globenewswire.com/NewsRoom/AttachmentNg/86a9bacd-000b-4915-ba56-58f9637f2460

The technical information in this news release has been prepared in accordance with the Canadian regulatory requirements set out in NI 43-101 and reviewed and approved by Michael R. Smith, SME Registered Member (Geology), who is a “Qualified Person” as defined by NI 43-101 for this project.

Quality Assurance and Quality Control Statement

Procedures have been implemented to assure Quality Assurance Quality Control of drill hole assaying being done at an ISO Accredited assay laboratory. Drill hole samples to be assayed are securely stored for shipment, with chain of custody documentation through delivery. Mineralized commercial reference standards or blank standards are inserted approximately every 20th sample in sequence and results are assessed to ascertain acceptable limits for analytical variance. Duplicate samples will also be taken as a further check in lab precision and accuracy. All results will be analyzed for consistency and corrective actions taken, if needed.

About Arizona Gold Corp.

Arizona Gold is an emerging American gold producer advancing the restart of production at its 100-per-cent-owned, fully permitted, past-producing Copperstone mine project, located in mining-friendly Arizona. The Copperstone mine project demonstrates significant upside exploration potential that has yet to be drilled within a 50 square-kilometre (12,258 acres) land package that includes past production of over 500,000 ounces of gold by way of an open-pit operation.

The company’s current focus is on maximizing Copperstone’s potential by defining and expanding current resources and further optimizing the mine’s economics for purposes of the restart of gold production in 2021 as a result of the recent project funding transaction entered into with Star Royalties Ltd.