QMX Gold Announces Ongoing Success at Bonnefond South Plug, Intersects 1.9 g/t Gold Over 84 Meters






QMX Gold Corporation (TSX-V:QMX) is pleased to report assay results from the second hole in a 4,500-meter drill program targeting the Bonnefond South Tonalite Plug on the east side of QMX Gold’s extensive land package in Val d’Or, Quebec (Figure 1).



Figure 1: Val d’Or Mining Camp Property – Current Activities

Highlights include:


  • The second hole, intersected the Tonalite Plug from the bedrock interface at 71.8 meters, down to a hole depth of 155.6 meters. The entire interval demonstrated alteration and veining typical of the mineralized zone and assayed 1.9 g/t gold over 83.8 meters (core length);
  • Within this interval, a sheared mafic dyke returned 4.9 g/t gold over 10.2 meters from 95.8 meters to 106.0 meters;
  • Four shear zones were also intersected within the footwall volcanic rocks below the Bonnefond South Plug. The shears are similar to those encountered in the first hole of this program [Press Release: September 13, 2017] with assay results of up to 7.0 g/t gold over 2.8 meters;
  • Eight holes for 3,807 meters have been completed to date, assays for holes 3 through 8 are pending.



“Drilling on our Val d’Or Mining Camp property continues to yield strong results. Combining these initial results on Bonnefond South with the discoveries announced earlier in 2017, our team is proving its ability to successfully identify, evaluate and target prospective areas across our large land package in the heart of the Val d’Or mining district,” commented Brad Humphrey, President and CEO. “The Bonnefond South drill program is successfully achieving its three primary goals, i) confirm AUR Resources’ results within the plug, ii) allow us to use down-hole core-orientation tools, and iii) test for the extension of mineralization outside of the plug. The results to date have exceeded our expectations.”



“The first two QMX drill holes confirm good continuity in widths and grades between the wider spaced historical holes. Further drilling and the use of oriented drill core will allow us to better define the potential for extensions of both the Tonalite Plug and mineralization,” stated David Rigg, Senior VP Exploration.



Result from Second Hole – 17315-17-026



The casing of the second hole was secured in bedrock at 71.8 meters. The hole entered directly into a shear zone interpreted to be at the north contact of the Bonnefond Tonalite Plug. The south contact of the Bonnefond Plug was intersected at 155.6 meters and is also a shear zone. The entire 83.8 meter interval, from 71.8 to 155.6 meters, is cut by a system of millimetric to decametric, auriferous quartz-tourmaline veins with associated alterations and minor Pyrite. The entire section assayed 1.9 g/t gold over 83.8 meters (Figure 2 and Table 1). The geological environment is very similar to that of the first hole of the program, 17315-17-25 [Press Release: September 13, 2017]. The broad intersection of tonalite in the second hole is also cut by a sheared and mineralized mafic dyke from 95.8 to 106.0 meters that assayed 4.9 g/t gold over 10.2 meters. Both of the shear zones delimiting the tonalite, the North Shear and the South Shear, are mineralized and assayed 0.80 g/t gold over 4.0 meters and 5.2 g/t gold over 6.6 meters, respectively.



Results from the second hole are consistent with the results from historic drilling completed by AUR Resources. AUR hole 315-22, 50 meters bellow the second QMX drill hole, intersected the Tonalite Plug and returned 2.0 g/t gold over 54.7 meters (Figure 2). The AUR intersection cut two sheared mafic dykes returning 4.2 g/t gold over 5.1 meters and 10.8 g/t gold over 3.2 meters. The alteration and veining described in the historical drill logs is very similar to that in QMX Gold’s hole 17315-17-025 and -026.




Figure 2: Schematic Geological Section of Hole 17315-17-026, Bonnefond South Plug



Within the footwall volcanic rocks underlying the plug to the south, four distinct zones of shearing were intersected. QMX believes these metric wide zones result from focused high strain deformation with associated alteration and anomalous gold values and are similar to those encountered in the first hole of the program. The best gold intersection from the second hole associated with these shears is 7.0 g/t gold over 2.8 meters.




Table 1: Technical Parameters and Assay Results – Hole 17315-17-026
Hole Number MTN Zone 9, Nad 83 MTM Zone 9, Nad 83 Azimuth Dip Hole Length From To Length* Au** Description
  Easting Northing (°) (°) (meters) (meters) (meters) (meters) (g/t)  
17315-17-026 232100 5330438 180 -55 402 71.8 155.6 83.8 1.9 Tonalite
          Including 71.8 75.8 4.0 0.8 North Shear Zone
          Including 95.8 106.0 10.2 4.9 Sheared Mafic Dyke
          Including 150.4 155.6 5.2 6.6 South Shear Zone
            193.8 197.0 3.2 1.0 Shear Zone
            210.7 214.2 3.5 1.7 Shear Zone
            277.8 280.8 3.0 0.5 Shear Zone
            372.8 375.6 2.8 7.0 Shear Zone



* Reported length are measured along the hole.

** Au uncut.



Hole 27325-27-026 was drilled with an azimuth of 180° and a dip of -55° to validate the geometry and the extension of the sheared mafic dykes. A detailed review of the geology and a description of the current drilling program is available in a press release dated September 13, 2017.



At this stage in the program, it is too early to define the direction and dip of all the individual structures and components that combine and contribute to the overall shape and plunge of the tonalite plug and mineralized zone(s). All drill holes are NQ-sized and will be surveyed at the end of the program using the Optical and Acoustic Imaging tool from PanPacific Wireline Services. Prior drilling was AQ-sized, which is not amenable to the survey equipment.



Qualified Persons



The scientific and technical content of this press release has been reviewed, prepared and approved by Mr. David Rigg, P.Geo, Senior Vice President Exploration, who is a “Qualified Person” as defined by National Instrument 43-101 – Standards of Disclosure for Mineral Projects.



About QMX Gold Corporation



QMX Gold Corporation is a Canadian based resource company traded on the TSX-V under the symbol “QMX”. The Company was recently restructured and is now systematically exploring its extensive property position in the Val d’Or mining camp in the Abitibi District of Quebec. QMX is currently drilling on the Bonnefond South Plug and is evaluating its recent discoveries on the Southwestern and Beacon Zones in order to develop follow up drill programs. In addition to its extensive land package, QMX owns the Aurbel gold mill.


Posted October 12, 2017


Rick Mills - "Bond Market Bear Creating Gold Bull"

Gold is climbing as bond yields rise and the dollar falls, over speculation that China is pulling ba... READ MORE

January 19, 2018


Larry W. Reaugh, President and Chief Executive Officer of American Manganese Inc. (TSX.V:AMY) (Pink ... READ MORE

January 19, 2018

Canadian Metals announces closing of private placement for $ 1,275,500

Canadian Metals Inc. (CSE:CME) (CSE:CME.CN) (CNSX:CME)annou... READ MORE

January 19, 2018

Metanor Intercepts 14.3g/t Au over 4.6 metres at Barry and moves towards underground bulk sample

Metanor Resources Inc. (TSX-V:MTO) is pleased to announce new hig... READ MORE

January 19, 2018

White Gold Intersects Gold Mineralization Supporting Continuity of the Arc Deposit, Encounters Gold on Newly Defined Target and on Schedule to Provide Updated Mineral Resource Estimate in Q1 2018

White Gold Corp. (TSX-V:WGO) is pleased to announce final reverse... READ MORE

January 19, 2018

Copyright 2018 The Prospector News - Site design by Spyderbaby Productions